Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
Body
Air central air
- The electric equipment
Specifications
Gymnastics system
The generator
Power failure check on a wire connecting the storage battery with the generator
Check of the current developed by the generator
Check of developed pressure
The generator of petrol engines
The generator of the diesel engine
The storage battery
Start system
Starter of petrol engines
Starter of the diesel engine
Safety locks
The block of safety locks
The multipurpose switch
Sound signal
Combination of devices
The switch of position of a lay brake
Screen wiper and стеклоомыватель a windscreen
Screen wiper of back glass
Headlights and forward indexes of turn
Forward antifog headlights and turn repeaters
The back combined lantern
The top stoplight
Lantern of illumination of licence plate
The ceiling fixture (with the hatch)
The ceiling fixture (without the hatch)
Lamp of illumination of salon
Check of the relay of headlights
Radio receiver
Heater of back glass
Safety pillows (SRS)
Seat belts
Search and elimination of malfunctions
Specification for adjustments and the control
Electric schemes
|
Combination of devices
Removal and installation
|
|
|
|
Disconnect a wire from the negative plug of the storage battery
|
Turn out screws of fastening of a combination of devices.
Remove an ashtray, then turn out screws of fastening of a combination of devices.
|
|
Disconnect sockets from a combination of devices. Remove a combination of devices.
|
|
|
Installation is spent to sequences, return to removal.
|
|
|
Speedometer check
|
|
Adjust pressure in tyres.
Establish the car on the stand for check of a speedometer and establish wedges under back wheels.
Check up, whether there are indications of a speedometer within the admission resulted in specifications.
|
|
|
|
At speedometer check suddenly do not press a pedal of coupling and sharply do not increase / reduce speed. |
|
|
Deterioration of tyres and inappropriate pressure in tyres leads to increase in an error of measurement of speed. |
Tachometre
|
|
Connect a test tachometre.
Start the engine. Compare indications of a speedometer of the car to indications of a test tachometre. If the difference of indications exceeds admissible values, replace a tachometre.
|
|
|
|
- Реверсирование a tachometre will lead to damage of semi-conductor devices in a tachometre.
- At removal and tachometre installation be cautious not to drop or strike it.
|
The index of level of fuel
|
|
Include ignition.
|
|
Connect a lamp capacity of 3,4 Vt and working pressure 12 In to plugs 1 and 3.
|
Include ignition and be convinced that the control lamp burns in full heat and the marksman of the index shows a full tank.
|
|
Resistance check
|
|
Remove a combination of devices.
Connect variable resistance to plugs 11 (M09–1) and 13 (M09–1). Check up that the index shows fuel level according to resistance change. Otherwise replace the index of level of fuel.
|
Resistance, Ohm
|
Level
|
|
97
|
Е (Empty)
|
|
32,5
|
1/2
|
|
6
|
F (Full)
|
|
|
The gauge of level of fuel
|
|
By ohmmeter measure resistance between contacts 1 and 3 in each position of a float.
| Float position |
F
|
1/2
|
E
|
| Resistance, Ohm |
3
|
32,5
|
110
|
|
|
Also be convinced that at moving of a float from position E in position F resistance changes smoothly.
|
|
|
The temperature index
|
|
|
|
By ohmmeter measure resistance between contacts 2 and "weight".
|
If resistance do not correspond resulted in the table, replace the temperature index.
| Temperature, C |
60
|
85
|
110
|
125
|
| Resistance, Ohm |
119,4
|
48,9
|
25
|
15,8
|
|
|
The gauge of pressure of oil
|
|
|
|
Be convinced that at the switched off engine there is a conductivity between contact of the gauge and "weight".
|
Be convinced that at the working engine there is no conductivity between contact of the gauge and "weight".
Otherwise replace the gauge of pressure of oil.
|
|
|
|