Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
Body
Air central air
- The electric equipment
Specifications
Gymnastics system
The generator
Power failure check on a wire connecting the storage battery with the generator
Check of the current developed by the generator
Check of developed pressure
The generator of petrol engines
The generator of the diesel engine
The storage battery
Start system
Starter of petrol engines
Starter of the diesel engine
Safety locks
The block of safety locks
The multipurpose switch
Sound signal
Combination of devices
The switch of position of a lay brake
Screen wiper and стеклоомыватель a windscreen
Screen wiper of back glass
Headlights and forward indexes of turn
Forward antifog headlights and turn repeaters
The back combined lantern
The top stoplight
Lantern of illumination of licence plate
The ceiling fixture (with the hatch)
The ceiling fixture (without the hatch)
Lamp of illumination of salon
Check of the relay of headlights
Radio receiver
Heater of back glass
Safety pillows (SRS)
Seat belts
Search and elimination of malfunctions
Specification for adjustments and the control
Electric schemes
|
Starter of petrol engines
Removal and installation
|
|
Disconnect a wire from the negative plug of the storage battery.
Disconnect a cable of a drive of a speedometer and a gear change.
Disconnect from a starter a socket and a wire from the plug.
Turn out bolts and remove a starter.
Installation is spent to sequences, return to removal.
|
|
Check and replacement of elements статора
Adjustment of a backlash of a gear wheel
|
|
Disconnect a wire of the engine of a starter from plug "M".
|
|
Additional wires connect plugs of the storage battery to plugs "S" and "M".
|
Include ignition, thus a starter gear wheel it will be pushed forward.
|
|
This check is necessary for executing during 10 with as, otherwise, can fuse the solenoid of the traction relay. |
|
|
Щупом check up a backlash between a gear wheel and a stopper. If the backlash differs from demanded, adjust it, adding or cleaning linings between the traction relay and a forward cover. A gear wheel backlash: 0,5–0,2 mm.
|
|
|
Check of the traction relay of a starter
|
|
Disconnect a wire of the engine of a starter from plug "M".
|
|
Additional wires connect plugs of the storage battery to plugs "S" and "M".
|
Include ignition, thus a starter gear wheel it will be pushed forward. If the gear wheel is not put forward, replace the traction relay.
|
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
Check of a keeping winding of the traction relay
|
|
|
|
Disconnect a wire of the engine of a starter from plug "M".
Additional wires connect plugs of the storage battery to plug "S" and the case of the traction relay.
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
|
If the gear wheel remains on a place, means, the keeping winding of the traction relay is damaged and, it is necessary to replace the traction relay.
|
|
Return check плунжера the traction relay
|
|
Disconnect a wire of the engine of a starter from plug "M".
Additional wires connect plugs of the storage battery to the plug of M and the case of the traction relay.
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
|
|
The starter gear wheel should be pushed forward. After a detachment of wires the starter gear wheel quickly should return to a starting position.
|
|
|
Operational tests (idling)
|
|
|
|
For carrying out of tests of idling collect the scheme shown in drawing.
|
Establish a rheostat cursor in such position at which the voltmeter will show pressure 11,5 In, thus check up a current consumed by a starter, and be convinced that the starter shaft is turned easily and smoothly. A current: no more than 60 And.
|
|
Gear wheel with обгонной муфтой
To remove обгонную муфту from a rotor shaft, it is necessary to remove a persistent ring preliminary.
|
|
Move a persistent ring to a gear wheel and remove a spring ring. Now the persistent ring can be removed from a shaft.
|
Check of a winding of a rotor
|
|
|
|
Ohmmeter check up conductivity between a collector and a rotor. In the presence of conductivity replace a rotor.
|
|
|
In the special device check up a rotor winding. In the presence of short circuits replace a rotor. If the steel strip enclosed to a rotor, vibrates, means, in rotor windings there are short circuits.
|
|
|
Ohmmeter check up conductivity between collector segments. In the absence of conductivity replace a rotor.
|
|
|
Check of coils статора
|
|
|
|
Ohmmeter check up conductivity of coils статора. In the absence of conductivity replace coils статора.
|
|
|
With the coil established in the case, check up conductivity between a conclusion of the coil and the starter case. In the presence of conductivity replace coils статора.
|
|
|
Check of brushes
|
|
If the brush is worn out to the designated limit, replace it.
|
Check щеткодержателя
|
|
Ohmmeter check up conductivity between each isolated brush and a plate. In the presence of conductivity replace щеткодержатель.
|
Check обгонной муфты
|
|
Check up a condition of teeths of a gear wheel обгонной муфты and, in the presence of damages, replace it. Also check up a condition of teeths of a gear wreath of a flywheel.
|
|
Turn a gear wheel. The gear wheel should be turned freely clockwise and be blocked at проворачивании counter-clockwise
|
|
|
Replacement of brushes
|
|
Remove the worn out brush, thus be careful not to damage a wattled wire.
Emery paper smooth out the end of a wattled occasion to provide its reliable contact to a new brush.
|
|
Replacement of the back plug
|
|
Before to remove the plug, it is necessary to measure depth of its installation.
|
|
The plug can be removed by means of a stripper, as is shown in drawing.
|
Establish the new plug on preliminary measured depth.
|
|
Starter assemblage
|
|
Establish обгонную муфту on the forward end of a shaft of a rotor.
|
|
Establish a persistent ring and a spring ring from the forward party of a shaft of a rotor then move a persistent ring completely to a spring ring.
|
|
|
At lever installation in a forward cover pay attention to its position. If the lever to establish on the contrary, the gear wheel will be put constantly forward outside and cannot work properly.
|
|
|
The switch of blocking of ignition
|
|
Check up that the installation height, a free wheeling and a backlash of a pin with a head and an aperture under pin coupling pedals are in normal limits.
|
Check of the relay of a starter
|
|
Remove the relay of a starter and check up conductivity between its plugs. If conductivity does not correspond demanded, replace the relay.
|
Check of the switch of blocking of ignition
|
|
Check up conductivity between plugs of the switch of blocking of ignition.
|
|
|