Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
- Brake system
   Specifications
   Check of the vacuum amplifier of brakes
   Check of the unilateral vacuum valve
   Prorolling of hydraulic system of a drive of brakes
   Adjustment of a course of a lay brake
   Brake pedal
   The vacuum amplifier of brakes
   The main brake cylinder
   Replacement of lobbies brake pads
   Support of a forward brake
   Back disk brakes
   Back drum-type brakes
   Replacement of the working brake cylinder
   Pressure regulator
   Brake tubes and hoses
   Lay brake
   Antiblocking system of brakes (ABS)
   Hydraulic block HECU
   The gauge of frequency of rotation of a wheel
   Prorolling of hydraulic system of a drive of brakes with scanner use
   Search and elimination of malfunctions
Body
Air central air
The electric equipment
Electric schemes










Support of a forward brake

Removal

 PERFORMANCE ORDER

    Remove a forward wheel. Turn out a hollow bolt and disconnect from a support a brake hose.

For an exception leakage a brake liquid close an aperture in a brake hose a suitable stopper.

    Turn out bolts of fastening of a support. Remove a support and brake pads. Turn out bolts of fastening of the holder of a support to a rotary fist.
    Remove a fixing element of a support.

Check

 PERFORMANCE ORDER

    Check up a support on absence of deterioration, damages, cracks and a rust. Check up the piston on absence of a rust, damages, cracks and deterioration of an external surface. Check up the plug and directing finger on absence of damages and a rust. Check up a spring and covers on absence of damages. Check up a fixing element on absence of deterioration, damages, cracks and a rust.
  1. Do not use an emery paper for clearing of a surface of the piston.
  2. It is necessary to replace all rubber details with the new.
    Measure a thickness of a brake disk. By the indicator of hour type measure palpation of a brake disk on small distance from external edge.

Thickness of a brake disk:

The nominal: 24 mm
Is minimum admissible: 22,4 mm

Maximum permissible palpation: 0,08 mm
Maximum permissible difference of a thickness of a brake disk: 0,01 mm

  1. By micrometer measure a thickness of a disk in eight places, approximately through everyone 45 on distance of 10 mm from external edge of a disk.
  2. The indicator of hour type check up palpation of a brake disk. The indicator of hour type fix in any convenient place and, turning a brake disk, define its palpation on distance of 5 mm from external edge.
    If necessary, replace a brake disk.

Dismantling

 PERFORMANCE ORDER

    Remove a dustproof cover of the piston.
    Compressed air squeeze out the piston from the support cylinder.
  1. At piston expression by the compressed air have no fingers in front of the piston.
  2. Be careful, as from the channel the compressed air together with the piston blows a brake liquid.
    Screw-driver edge remove a sealing ring from the piston.

Assemblage

 PERFORMANCE ORDER

    Clear all details, except for brake pads, изопропиловым spirit.
    Put special greasing on a sealing ring of the piston and establish it in a piston flute.
    Collect the piston and piston covers in a following order:
    – Put special greasing on walls of the cylinder of a support, an external surface of the piston and a piston cover;
    – Establish a piston cover how it is shown in drawing;
    – Insert a piston cover into an internal flute of a support and move the piston into a support.
    Collect mobile details in a following order:

– Put special greasing on an external surface of the plug, directing finger and in an aperture for the plug and establish protective covers;

– Insert covers into support flutes.

    Establish brake pads.

Never put greasing on a brake disk and brake pads.

    Screw and tighten the demanded moment of an inhaling a hollow bolt of fastening of a brake hose.

The inhaling moments:

Directing finger: 35–45 Nm
Bolt of fastening of a directing finger: 22–33 Nm
Bolt of a fixing element of a support: 65–75 Nm
Hollow bolt of fastening of a brake hose: 25–30 Nm

  1. Before installation check up that surfaces of bolts and a directing finger are not damaged.
  2. Remove air from a hydraulic drive of brake system. Some times press a pedal of a brake and check up absence of leak of a brake liquid.

Installation

Installation is spent to sequences, return to removal.

 PERFORMANCE ORDER

    Establish brake pads and a support. Never put greasing on a brake disk and brake pads. Screw and tighten the demanded moment of an inhaling a bolt of fastening of a support.
    Screw and tighten the demanded moment of an inhaling a hollow bolt of fastening of a brake hose.
    Fill in in a tank a brake liquid. Remove air from a hydraulic drive of brake system. Some times press a pedal of a brake and check up absence of leak of a brake liquid.