Hyundai Elantra
- Petrol engines 1,6, 1,8 and 2,0 l
   Compression check
   Gear belt
   Adjustment of a tension of a gear belt
   Tension adjustment поликлинового a belt
   Adjustment of a tension of a belt of a drive of the generator
   Camshafts
   Check and adjustment of backlashes of valves on engines of 1,8 and 2,0 l (MLA)
   Hydraulic jacks of backlashes of valves of the engine of 1,6 l
   Installation of a cover of a head of cylinders
   Directing to a chain
   Chain
   Installation of camshafts
   The mechanism of change of the moment of opening and closing of valves (CVVT) on engines of 1,8 and 2,0 l
   Repair of a head of cylinders
   Engine support
   Removal and engine and transmission installation
   The block of cylinders
   Cranked shaft
   Flywheel
   The piston
   The air filter (ACL)
   Final collector
   Inlet collector
   System of release of the fulfilled gases
   Search and elimination of malfunctions
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
Body
Air central air
The electric equipment
Electric schemes









Camshafts

Removal

 PERFORMANCE ORDER

    Disconnect a ventilation hose картера.
    Remove a pulley of the water pump and a cranked shaft.
    Remove a casing of a gear belt. Take away a roller of a tension of a gear belt and temporarily fix it in this position. Remove a gear belt from a camshaft pulley. Turn out screws and remove the central cover. Remove the block of coils of ignition.
    Turn out bolts and uncover heads of cylinders.
    Remove a camshaft pulley.
    Remove covers of bearings of a camshaft and a chain.
    Remove camshafts. Remove adjusting linings and pushers.
  1. Arrange adjusting linings and pushers in such order, that at сборкса. If the working edge is worn out or damaged, replace a sealing ring.
  2. Check up the surface of a camshaft contacting to a sealing ring. If this surface is worn in regular intervals out, replace a camshaft. е they were established in initial positions.

Check

Camshafts

 PERFORMANCE ORDER

    Check up a camshaft on absence of non-uniform deterioration, cracks or damages.
    In two points measure height of each cam of a camshaft.

Nominal height of cams of a camshaft of inlet valves:

- Engines of 1,8 and 2,0 l, except CVVT: 44.820 mm;
- Engines of 1,6 l: 43,4484 mm.

Nominal height of a camshaft of final valves:

- Engines of 1,8 and 2,0 l, except CVVT: 44.720 mm;
- Engines of 1,6 l: 43,8489 mm.

Is minimum admissible height of cams of a camshaft of inlet valves:

- Engines of 1,8 and 2,0 l, except CVVT: 44.720 mm;
- Engines of 1,6 l: 42,9484 mm.

Is minimum admissible height of a camshaft of final valves:

- Engines of 1,8 and 2,0 l, except CVVT: 44.620 mm;
- Engines of 1,6 l: 43,3489 mm.

    Check up surfaces of cams on absence of non-uniform deterioration and damages. Check up each bearing on absence of damages. If the working surface of the bearing is excessively damaged, replace a head of cylinders or a cover of the bearing of a camshaft.

Axial люфт a camshaft:

- Engines of 1,8 and 2,0 l: 0,1–0,2 mm;
- Engines of 1,6 l: 0,1–0,15 mm.

Forward sealing ring of a camshaft

 PERFORMANCE ORDER

    Check up working edges of a sealing ring on absence of deterioration. If the working edge is worn out or damaged, replace a sealing ring.
    Check up the surface of a camshaft contacting to a sealing ring. If this surface is worn in regular intervals out, replace a camshaft.