Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
- The diesel engine of 2,0 l
Specifications
Compression check
Adjustment of a tension of a gear belt
Gear belt
Cover of a head of cylinders and a stopper
Camshaft
Balancing shaft
Repair of a head of cylinders
Engine support
The elements of support which are subject to check
The block of cylinders
Removal and engine and transmission installation
Cranked shaft
The piston
Турбокомпрессор
Cooler of inflated air
The air filter (ACL)
System of release of the fulfilled gases
Search and elimination of malfunctions
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
Body
Air central air
The electric equipment
Electric schemes
|
Gear belt
Removal
|
|
Turn a cranked shaft clockwise and combine adjusting labels that the piston in the first cylinder was established in the top dead point in a compression step. At this time adjusting labels of a pulley of a camshaft and a cover of a head of the block of cylinders should be combined, and the adjusting pin of a pulley of a camshaft should be above. |
|
|
Remove поликлиновой a belt and a pulley of a cranked shaft.
Remove a casing of a gear belt.
Remove an arm of a support of the engine.
|
|
For a head of the big bolt turn the mechanism of a tension of a gear belt before combination of a basic plate with an aperture in a casing, then insert a clamp into an aperture.
|
|
|
Shestigrannym key loosen the a fixing bolt.
|
|
|
For a head of the big bolt turn the mechanism of a tension of a gear belt against the stop clockwise.
|
|
|
Tighten fixing bolt.
|
Remove a gear belt.
|
|
Note a direction of rotation of a gear belt for its repeated installation in initial position. |
|
|
Turn out шарнирный a bolt and remove the mechanism of an automatic tension of a gear belt.
|
|
|
Check
Pulleys, pulley of the mechanism of a tension of a gear belt and single pulley
|
|
. Check up pulleys of distributive and cranked shaft, a pulley of the mechanism of a tension and a single pulley on absence of non-uniform deterioration, cracks and damages. Replace them as required.
Check up ease and smoothness of rotation of a pulley of the mechanism of a tension and a single pulley, and also absence of extraneous noise at rotation. Replace them as required.
|
|
Replace pulleys if there is a lubricant leak.
|
|
|
The mechanism of an automatic tension of a gear belt
|
|
Check up the mechanism of an automatic tension of a gear belt on absence of leaks and, if necessary, replace it.
|
|
Check up a tip on absence of deterioration or damages and, if necessary, replace it.
|
|
|
Gear belt
|
|
Check up a gear belt on absence of traces of oil, water or a dust. If it is necessary replace a belt. Insignificant traces should be threadbare by a dry fabric or a paper. Do not clean a gear belt solvent.
After repair of the engine or adjustment a belt tension, check up a belt condition. In the presence of following defects, replace a gear belt.
|
|
Installation
|
|
Establish a pulley of a cranked shaft on a cranked shaft.
|
|
Special attention turn on a direction of installation of a flange. If the pulley is established incorrectly, it will lead to damage of a gear belt. |
Establish a special washer and screw a bolt of fastening of a pulley to a cranked shaft and then tighten a bolt. The inhaling moment: 185–195 Nm.
|
|
Gear belt
|
|
Check up position of adjusting labels.
From outside a cranked shaft: an adjusting label on a pulley of a cranked shaft and a rod for installation of the moment of injection;
From outside a camshaft: an adjusting label on a pulley of a camshaft and a head of cylinders.
Establish the tension mechanism.
Establish the mechanism of an automatic tension of a gear belt.
|
|
Tighten шарнирный a bolt. The inhaling moment: 50–55Nm.
|
Establish a gear belt.
|
The description
|
Defect
|
| 1. A rigid return surface of a gear belt |
|
|
The surface has a glossy appearance. Rigidity of a surface is that that the nail does not leave traces on a belt
|
|
| 2. Cracks on a return surface of a gear belt |
|
| 3. Cracks or stratification of a gear belt |
|
| 4. Strongly worn out teeths |
|
|
The tooth party is worn out, fibres, a cord and the rubber basis become thus visible
|
|
| 5. Strongly worn out teeths (last stage) |
|
|
The tooth party is worn out, attritions become thus visible and the thickness of a tooth is reduced
|
|
| 6. Cracks in the basis of teeths |
|
| 7. Absence of a tooth |
|
| 8. Strong deterioration of one party of a belt |
|
|
The normal belt should have an equal lateral end face, as though cut off by a sharp knife
|
|
| 9. Cracks on a lateral face of a gear belt |
|
Loosen the the fixing bolt, thus will move the lever of the mechanism of a tension and will automatically pull a gear belt.
|
|
Turn clockwise a cranked shaft of the engine on two turns and check up combination of adjusting labels.
|
Tighten fixing bolt.
Remove a clamp.
|
|
|
|