Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
- Coupling
Specifications
Adjustment of a pedal of coupling
Prorolling of hydraulic system of a drive of coupling
Conducted and press coupling disks
The main cylinder of coupling
Coupling pedal
The working cylinder of coupling
Search and elimination of malfunctions
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
Body
Air central air
The electric equipment
Electric schemes
|
Conducted and press coupling disks
Removal
|
|
Merge oil from a transmission and a brake liquid from a hydraulic drive of coupling.
Remove a transmission.
Establish the mandrel 09411–25000 for a centering of a disk of coupling which in this case will exclude falling of a conducted disk of coupling.
Gradually on a diagonal loosen the bolts of fastening of coupling in gathering.
|
|
Turn on each bolt on 1/2 turns until action диафрагменной springs will stop, and bolts can be unscrewed manually. Remove a casing of coupling with a press disk and a coupling disk.
|
|
|
Do not clear solvent a disk of coupling or the bearing of deenergizing of coupling. It is desirable to remove a flywheel and to check up a back sealing ring of a cranked shaft on absence of leaks. If necessary, replace a sealing ring. |
|
|
Check of a casing of coupling with a press disk
|
|
Check up диафрагменную a spring in places of contact to the bearing of deenergizing of coupling on absence of deterioration, cracks and define distinction of height of the ends диафрагменной springs. In the presence of defects replace a casing of coupling with a press disk.
Check up press a disk on absence of cracks, пригара and deterioration of a surface.
Check up reliability заклепочных connections.
|
|
Check of a disk of coupling
|
|
Check up reliability заклепочных connections of frictional overlays to a coupling disk. In the presence of defects replace a coupling disk.
|
|
Measure a thickness of a brake disk.
|
Check up a condition of frictional overlays of a disk of coupling and at presence with them of traces of oil or mechanical damages replace a coupling disk.
Clear Slots a primary shaft of a transmission and establish on a shaft a coupling disk. If the coupling disk moves on a shaft hardly or too big backlash in шлицевом connection, replace a disk of coupling and / or an entrance shaft.
|
|
Check of the bearing of deenergizing of coupling
|
|
The bearing of deenergizing of coupling is tight, and it cannot be washed out. |
|
|
Check up a condition of the bearing of deenergizing of coupling which should rotate easily, in regular intervals and silently and in it should be absent люфт. The working surface of the bearing influencing a press spring, should be smooth, without cracks, local corrosion or development.
The faulty bearing of deenergizing of coupling can be defined, without removing it from the car for what it is necessary to press a coupling pedal at the working engine. If by pressing of a pedal of coupling there is an additional noise, means, the bearing of deenergizing of coupling is faulty, and it is necessary to replace it.
|
|
Check of a plug of deenergizing of coupling
If there is a non-uniform deterioration in points of contact of a plug of deenergizing of coupling with the bearing, replace a plug of deenergizing of coupling.
Installation
|
|
Put greasing on surfaces of contact of the bearing, the cylinder and a plug of deenergizing of coupling.
Greasing: MOLYWHITE TA № 2.
|
|
|
|
At coupling installation put greasing on all mobile connections of details, but do not use excessive quantity of greasing as it can lead to coupling proslipping. |
|
Establish a disk of coupling and centre its special оправкой 09411–25000.
|
|
Establish a casing of coupling with a press disk on directing pins of a flywheel. Gradually, in diagonal sequence and in a certain order, tighten bolts of fastening of a flywheel. The inhaling moment: 15–22 Nm.
|
|
|
Connect the bearing to a plug of deenergizing of coupling and establish it on the casing plug.
|
|
|
Apply a thin film greasings MOLYWHITE TA № 2 on a groove of the basic plug and a point of contact of a plug of deenergizing of coupling. |
Establish squeezing the lever on a plug of deenergizing of coupling.
|
|
If the transmission is fixed on the engine, do not carry out this step as the bearing of deenergizing of coupling can be separated in spite of the fact that the plug of deenergizing of coupling turns freely. |
|
|
Establish a transmission.
|
|
|
After performance of the actions resulted in a step 6, press squeezing the lever in a direction of an arrow and be convinced that the bearing of deenergizing of coupling and a casing are correctly connected. The angle of rotation of the squeezing lever should be no more than 3 . If the angle of rotation of the squeezing lever more than 3 , means, the bearing of deenergizing of coupling and a casing are connected incorrectly.
|
|
|
|
|