Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
- Power shafts, forward and back axes
Specifications
Power shaft
Power shaft with SHRUS of ball type and Birfield type
Power shaft with SHRUS Birfield (B. J.) and трипоидного type (T. J.)
Rotary fist and nave of a forward wheel
Back axis/nave of a back wheel
Search and elimination of malfunctions
Suspension bracket
Steering
Brake system
Body
Air central air
The electric equipment
Electric schemes
|
Power shaft with SHRUS of ball type and Birfield type
Dismantling
|
- Do not assort the SHRUS of type Birfield.
- For greasing of SHRUS use only special greasing.
- At SHRUS assemblage it is necessary to establish new collars.
|
|
Remove collars and pull together a protective cover from a ball SHRUS of a power shaft.
|
Be careful not to damage a protective cover. |
|
Screw-driver with a flat edge remove a lock ring.
|
|
Remove a ball SHRUS from a power shaft.
|
|
Remove a spring lock ring, take out an internal ring, the case and balls in gathering.
|
Without dismantling clear an internal ring, the case and balls.
Remove collars and pull together protective covers of a ball SHRUS and SHRUS Birfield.
|
|
If the protective cover is repeatedly used before removal of a cover for its protection, wrap up Slots a power shaft a sticky tape. |
|
|
|
Check
|
Check up a ball SHRUS on absence of traces of a rust, damages of an external ring, an internal ring and balls.
Check up a condition шлицов a power shaft.
Check up on absence of traces of a rust, water and extraneous subjects in a protective cover of SHRUS Birfield.
|
|
If SHRUS Birfield has to be used repeatedly, do not delete from it greasing. Be convinced that in greasing there are no impurity. If necessary clear SHRUS Birfield and replace in it greasing. |
|
|
|
Assemblage
|
Before installation of a cover for its protection wrap up Slots a power shaft from outside the ball hinge a sticky tape.
Put greasing on a power shaft and establish a cover.
|
For installation dynamic damperа arrange SHRUS Birfield on a straight line in relation to a shaft, arrange damper on certain distance and fix its clip.
Installation distance damperа (A)
– Cars with engines of 1,6 and 1,8 l with МКП: 467,5 (2/0) mm – Cars with engines 2,0 with МКП: 469 (2/0) mm
|
|
Put greasing on an internal ring and the case. Establish the case so that displacement on a surface качения settled down, as is shown in drawing.
|
|
Use the greasing delivered together with the repair complete set. |
Put greasing on the case and the balls located in the case.
Establish the hinge, as is shown in drawing, and fix its spring lock ring.
Enclose demanded quantity of greasing in an external ring and establish it on a power shaft.
Enclose demanded quantity of greasing in a protective cover and establish a cover on the hinge.
Fix collars a protective cover of ball type.
Add in SHRUS Birfield so much greasing, how many it has been wiped during hinge check.
Establish covers.
Fix a protective cover of SHRUS Birfield collars.
|
For the control of pressure of air in hinge T.J cover. Support the demanded distance between collars of fastening of a protective cover or length of a power shaft at a tightening of collars. The nominal length of power shafts is resulted in the table.
|
Nominal length of power shafts with SHRUS of ball type and Birfield
The name
|
Left-hand side
|
The right party
|
Cars with engines of 1,6 l with МКП |
512,7 (22,8/–15,1) mm
|
795,7 (22,8/–15,1) mm
|
Cars with engines of 1,8 l with МКП |
795,2 (22,7/–14,4) mm
|
513,2 (22,7/–14,4) mm
|
Cars with engines of 2,0 l with МКП |
513,2 (20,7/–15,5) mm
|
796,2 (20,7/–15,5) mm
|
|
|
|
|