Hyundai Elantra
Petrol engines 1,6, 1,8 and 2,0 l
The diesel engine of 2,0 l
Greasing system
Cooling system
Fuel system
Monitoring systems and decrease in toxicity of the fulfilled gases
Ignition system
System of preliminary heating of the diesel engine
Coupling
Mechanical transmission
Automatic transmission
Power shafts, forward and back axes
Suspension bracket
Steering
Brake system
- Body
Specifications
Adjustment of hinges of a cowl
Luggage carrier cover
Luggage space door
Forward door
Back door
Молдинги
The roof hatch
The console
The panel of devices
Ceiling furnish
Internal upholstery of salon
Forward bumper
Back bumper
Sitting lobbies
Back seat
Seat belts
Humeral seat belt of back sitting
Zone seat belt of back sitting
Search and elimination of malfunctions
Air central air
The electric equipment
Electric schemes
|
The roof hatch
Removal
|
|
Before hatch removal remove following elements:
– A lamp from the top console;
– Sun-protection peaks and an internal rear-view mirror;
– An upholstery of a forward rack.
|
|
Remove the decorative panel and the glass panel of the hatch. The inhaling moment: 4–6 Nm.
|
|
|
Disconnect a drainage hose.
|
|
|
Turn out bolts and nuts and remove the hatch in gathering.
The inhaling moment:
Assembly bolts of the hatch: 7–11 Nm
Assembly nuts of the hatch: 4–6 Nm
|
|
|
|
|
At hatch removal in gathering be careful not to damage adjacent elements of the car. |
Dismantling
|
|
|
|
Remove sun-protection шторку.
|
|
|
Remove knot of the directing.
|
Remove the block of a drive with the electric motor.
|
|
|
|
|
|
At removal of the engine the knot ползуна should be in completely closed position. If there is a discrepancy between the glass panel and an engine ring in completely closed position, the hatch will not function привильно. |
|
Installation
Installation is spent to sequences, return to removal.
|
|
|
|
Check up that trailer switches of the engine (LS1 and LS2) are completely closed. Establish the centre of a directing roller and a label ползуна in completely closed position. |
|
Check of functioning after installation
If the hatch moves slowly, execute following adjustments and checks.
|
|
Be convinced that the storage battery is completely charged.
Be convinced that in knot ползуна there are no abrasive materials.
Be convinced that at opening of the glass panel of the hatch, the back part of the panel does not cling to the roof panel. In the presence of a backlash, completely open the glass panel and move a stopper.
|
|
If a stopper will advance too far, it can lead to failures in work and leaks. Be convinced that a backlash between the glass panel and the panel of a roof no more than 0,3 mm. |
|
|
Measure effort of the block of a drive of the hatch and, rotating a nut of adjustment of a twisting moment on the drive block, adjust it to 15–25 kg.
|
|
|
After adjustment be convinced that have blocked a nut a washer with a clamp.
|
|
|
Adjustment
|
|
Adjust height of installation of the glass panel of the hatch in relation to the roof panel.
The forward party: 0 (0,–1,0) mm
The back party: 0 (1, 0) mm
|
If the height of installation of the glass panel of the hatch in relation to the roof panel does not correspond demanded, adjust it as follows.
|
|
|
|
Loosen the forward and back screws. Adjust height of installation of the glass panel of the hatch in relation to the roof panel.
|
|
|
Loosen the nuts of fastening of the glass panel also adjust a backlash between the glass panel and the roof panel.
|
|
|
|
|